User Manual
Eg012Li Mini Portable Power Station
100W LiFePO4 Portable Power Station · Compact Outdoor Camping Emergency Power Bank
Precautions for Use
- Open the package and check whether the following accessories are complete: 1× Portable Power Station, 1× Charger, 1× User Manual. Please check carefully whether the device is damaged during transportation. If you find that the device is damaged or parts are missing, please do not start the device, and immediately notify the carrier and dealer.
- The device should be placed in a well-ventilated place away from water, flammable gases and corrosive substances.
- Do not place it on its side. Keep the bottom and panel of the device uncovered.
- The panel temperature and the working environment temperature of the device should be kept between 0°C ~ 40°C.
- If the device is disassembled and used at low temperature, water condensation may occur. It must be used only after the inside and outside of the device are completely dry, otherwise there will be a danger of electric shock.
Safety Precautions
- The device has high-voltage AC output, which is potentially dangerous. It must be handled with care and kept away from children, otherwise there will be a risk of electric shock.
- Do not connect the inverter of the device to the AC circuit, otherwise even if the switch of the device is turned off, the inverter may be damaged.
- Please ensure that the power used by the electrical appliance is less than the rated output power of the device.
- Before the load is connected to the device, be sure to turn off the load switch before connecting it, and then turn on the load switch for use.
- It is recommended to charge the device for at least 10 hours before use. Insert the AC adapter charger into the charging port when charging. The device can also be used without charging, but the backup time will be less than the standard backup time.
- It is prohibited to connect half-wave loads (hair dryer, electric heating wire heater), high-power motors, laser printers, or high-power rectifier loads. The device will be automatically protected because of the excessive starting power during operation.
Protection Functions
Application Scenarios
Use Load Types
AC fans, DC fans, AC LED lights, DC LED lights, digital products, mobile phones, desktop computers, notebook computers, etc.
Function Description
Operation Method
Power On
- When there is no charging, press the power switch on the panel for more than 1 second, release it after the LCD display lights up, and then press the corresponding function switch at this time, there will be a corresponding output.
- If solar energy and DC charger are connected, the LCD screen will automatically light up. At this time, press the corresponding function switch, and there will be a corresponding output.
Power Off
- When there is no charging, press and hold the power switch on the panel for more than 3 seconds, release it after the LCD screen goes out, and then shut the portable power station down.
- If the solar energy and DC charger are connected, the LCD cannot be turned off, so turn off the corresponding function switches and turn off each output.
- When there is no charging and no output switches are turned on, it will automatically shut down after 10 seconds.
Note: The portable power station has DC under-voltage and over-voltage protection functions. When the battery is under-voltage or over-voltage, it will automatically shut down.
Technical Parameters
| Item | Specification |
|---|---|
| Model | Eg012Li |
| Rated Power | 100W |
| Output Waveform | Modified Sine Wave |
| AC Output Voltage | 220V / 110V ±15% |
| AC Output Frequency | 50Hz / 60Hz ±2Hz |
| Conversion Efficiency | Maximum value >90% |
| Charging Interface | External charger port & solar panel charging port: DC5521 × 1 (built-in solar intelligent controller) |
| AC Output Socket | Universal Socket |
| DC Output | DC 5V 2.4A × 2 USB; DC 12V 3A × 2, DC5521 |
| LED Light States | 4 states: bright, half-bright, flashing, off |
| Battery Type | LiFePO4 |
| Battery Capacity | 12.8V 76.8Wh |
| Solar Panel | 16V 20W (optional) |
| Charging Current | Maximum 2A |
| AC Charger | 15V 1A |
| Charging Time | After full discharge, battery capacity reaches 80% after charging for 10 hours |
| LCD Display | Battery capacity, battery voltage, state of charge, state of discharge |
| Heat Dissipation | Automatic cooling |
| Noise | 1 meter distance <45dB |
| Protection Functions | Low voltage, over-voltage, overload, over-temperature, short circuit |
| Product Features | 1. DC/AC fully isolated; 2. High-frequency design, small size; 3. Pure copper transformer, high efficiency, low no-load loss; 4. Microprocessor, digital control, all-round protection; 5. Built-in solar charger, intelligent charge and discharge management; 6. AC output and DC output have independent switch function |
| Operating Temperature | −10 ~ 40°C |
| Operating Humidity | 10% ~ 85% |
| Storage Temperature | −20 ~ 70°C (no condensation) |
| Storage Humidity | 5% ~ 90% |
| Material | ABS |
| Net Weight | ≈1 kg |
| Product Size (W×D×H) | 160 × 100 × 143 mm |
For the complete user manual with original layout, you can also download the PDF version.
Reviews
There are no reviews yet.